QuNi40 Rod – Laser Welding Wire Nickel NiTi3 / ERNi-1 (2.4155) – also Nickel-Steel & Grey Iron

QuNi40 is the titanium-alloyed nickel wire: EN ISO 18274 S Ni 2061 (NiTi3) · AWS A5.14 ERNi-1 · filler material no. 2.4155.The 3.3 % titanium is what sets it apart from the pure QuNi29. Titanium binds nitrogen and thus suppresses porosity — precisely what is needed for nickel-to-steel dissimilar joints and for repairs on grey cast iron (GG-GJL), where gases migrate from the base material into the weld pool. For matching pure-nickel joints without such influence, QuNi29 is the simpler alternative.Recommended base materials2.4060, 2.4061, 2.4066, 2.4068Commercial pure nickel grades, LC nickelNickel-clad steelsNickel-to-steel dissimilar jointsCast iron (GG-GJL) — repairs possible to a limited extentTypical applicationsPressure vessel and plant construction, chemical industryNickel-to-steel dissimilar jointsGrey iron repairs (GJL)Food industry, energy sectorProperties and advantagesTi 3.3 % — binds nitrogen, suppresses porositySuitable for nickel-to-steel dissimilar jointsGrey iron repairs possible to a limited extentWeld metal: Re 300 MPa · Rm 450 MPa · A 25 %Bobbin form: K125, K250, K80, MA125, SH253 — wire weight 100 g–500 g, Ø 0,2 mm – 0,8 mm. Material analysis (wt.-%)C 0.02 | Si 0.3 | Mn 0.3 | Fe 0.1 | Ti 3.3 | Ni balance

QuNi40 is the titanium-alloyed nickel wire: EN ISO 18274 S Ni 2061 (NiTi3) · AWS A5.14 ERNi-1 · filler material no. 2.4155.The 3.3 % titanium is what sets it apart from the pure QuNi29. Titanium binds nitrogen and thus suppresses porosity — precisely what is needed for nickel-to-steel dissimilar joints and for repairs on grey cast iron (GG-GJL), where gases migrate from the base material into the weld pool. For matching pure-nickel joints without such influence, QuNi29 is the simpler alternative.Recommended base materials2.4060, 2.4061, 2.4066, 2.4068Commercial pure nickel grades, LC nickelNickel-clad steelsNickel-to-steel dissimilar jointsCast iron (GG-GJL) — repairs possible to a limited extentTypical applicationsPressure vessel and plant construction, chemical industryNickel-to-steel dissimilar jointsGrey iron repairs (GJL)Food industry, energy sectorProperties and advantagesTi 3.3 % — binds nitrogen, suppresses porositySuitable for nickel-to-steel dissimilar jointsGrey iron repairs possible to a limited extentWeld metal: Re 300 MPa · Rm 450 MPa · A 25 %TIG advantage: For larger seams and build-ups on nickel and cast components. Ø 1.0 mm.TIG form: for manual repair welding. Material analysis (wt.-%)C 0.02 | Si 0.3 | Mn 0.3 | Fe 0.1 | Ti 3.3 | Ni balance

QuNi29 is a pure nickel alloy Ni99.7Mg (material no. ~2.4060) for joint and build-up welding on commercial pure nickel grades, LC nickel, nickel alloys and nickel-clad steels.The difference from QuNi40 is stated in the datasheet: this wire is pure nickel without titanium. Where the electrical and thermal conductivity of nickel matters, this is the right choice. Where dissimilar joints to steel or cast iron repairs are involved, use the titanium-alloyed QuNi40 — its titanium binds nitrogen and prevents porosity.Recommended base materials2.4060, 2.4061, 2.4066, 2.40682.4052, 2.4053Commercial pure nickel grades, LC nickelNickel-clad steelsTypical applicationsPressure vessel and plant constructionChemical industryFood industryEnergy sector — where conductivity is requiredProperties and advantagesNi 99.7 % — pure nickel, no titanium additionGood corrosion and temperature propertiesPreserves the electrical and thermal conductivity of nickelMagnesium micro-alloyed (0.03–0.07 %) for clean weld metalRod form advantage: Constant wire feed for manual repair welding on vessels and apparatus.Rod form: Rod lengths 1000 mm and 333 mm, Ø 0,2 mm – 0,8 mm. Material analysis (wt.-%)Ni 99.70 | C 0.05 | Si 0.01 | Mn 0.10 | Cu 0.03 | Fe 0.07 | Mg 0.03–0.07

QuNi29 is a pure nickel alloy Ni99.7Mg (material no. ~2.4060) for joint and build-up welding on commercial pure nickel grades, LC nickel, nickel alloys and nickel-clad steels.The difference from QuNi40 is stated in the datasheet: this wire is pure nickel without titanium. Where the electrical and thermal conductivity of nickel matters, this is the right choice. Where dissimilar joints to steel or cast iron repairs are involved, use the titanium-alloyed QuNi40 — its titanium binds nitrogen and prevents porosity.Recommended base materials2.4060, 2.4061, 2.4066, 2.40682.4052, 2.4053Commercial pure nickel grades, LC nickelNickel-clad steelsTypical applicationsPressure vessel and plant constructionChemical industryFood industryEnergy sector — where conductivity is requiredProperties and advantagesNi 99.7 % — pure nickel, no titanium additionGood corrosion and temperature propertiesPreserves the electrical and thermal conductivity of nickelMagnesium micro-alloyed (0.03–0.07 %) for clean weld metalBobbin form: K125, K250, K80, MA125, SH253 — wire weight 100 g–500 g, Ø 0,2 mm – 0,8 mm. Material analysis (wt.-%)Ni 99.70 | C 0.05 | Si 0.01 | Mn 0.10 | Cu 0.03 | Fe 0.07 | Mg 0.03–0.07

QuMed4009 is a martensitic 13 % chromium steel to EN ISO 14343-A G/W 13 · AWS A5.9 ER410 (filler material no.: ~1.4009). Unlike the austenitic wires of the QuMed range, this weld metal hardens on cooling — it is a quench-and-temper material, not an austenite.The wire is intended for components that need corrosion resistance in water, gas and steam atmospheres, and for build-ups on unalloyed and low-alloy steels up to 450 °C. The weld metal is readily polishable and machinable, hardness as welded 150–225 HB.Recommended base materials1.4000, 1.4006, 1.4008 — martensitic 13 % Cr steelsAISI 410, AISI 420 — the corresponding US gradesBuild-ups on 1.2083 and 1.2085Build-ups on unalloyed and low-alloy steels up to 450 °CTypical applicationsStructural parts in water, gas and steam atmospheresBuild-ups on tool steels 1.2083 / 1.2085Components that are subsequently polishedRepairs on martensitic 13 % Cr componentsProperties and advantagesReadily polishable and machinable — the repair can be finished cleanlyCorrosion-resistant in water, gas and steamHardness as welded 150–225 HBWeld metal: Re 380 MPa · Rm 550 MPa · A 15 %Rod form advantage: Ideal for manual build-up welding with constant wire feed — also in hard-to-reach areas.Rod form: Rod lengths 1000 mm and 333 mm, Ø 0,2 mm – 0,6 mm. Material analysis (wt.-%)C 0.08 | Si 0.6 | Mn 0.65 | Cr 13.0 | Ni 0.4 | Fe balance

QuMed4009 is a martensitic 13 % chromium steel to EN ISO 14343-A G/W 13 · AWS A5.9 ER410 (filler material no.: ~1.4009). Unlike the austenitic wires of the QuMed range, this weld metal hardens on cooling — it is a quench-and-temper material, not an austenite.The wire is intended for components that need corrosion resistance in water, gas and steam atmospheres, and for build-ups on unalloyed and low-alloy steels up to 450 °C. The weld metal is readily polishable and machinable, hardness as welded 150–225 HB.Recommended base materials1.4000, 1.4006, 1.4008 — martensitic 13 % Cr steelsAISI 410, AISI 420 — the corresponding US gradesBuild-ups on 1.2083 and 1.2085Build-ups on unalloyed and low-alloy steels up to 450 °CTypical applicationsStructural parts in water, gas and steam atmospheresBuild-ups on tool steels 1.2083 / 1.2085Components that are subsequently polishedRepairs on martensitic 13 % Cr componentsProperties and advantagesReadily polishable and machinable — the repair can be finished cleanlyCorrosion-resistant in water, gas and steamHardness as welded 150–225 HBWeld metal: Re 380 MPa · Rm 550 MPa · A 15 %Bobbin form: K125, K250, K80, MA125, SH253 — wire weight 100 g–500 g, Ø 0,2 mm – 0,6 mm. Material analysis (wt.-%)C 0.08 | Si 0.6 | Mn 0.65 | Cr 13.0 | Ni 0.4 | Fe balance

Qu17-4PH is a precipitation-hardening, corrosion-resistant laser welding wire of the alloy 17-4PH (material 1.4542 / X5CrNiCuNb16-4, AISI 630). This martensitic chromium-nickel-copper steel combines high strength with good corrosion resistance — ideal for repair and build-up welding in tool and mould making as well as on pump, valve and shaft components.Recommended base materials1.4542 — X5CrNiCuNb16-4 / 17-4PH / AISI 630 (primary material)1.4540 — X4CrNiCuNb16-4 (identical-type variant)1.4548 — X5CrNiCuNb17-4 (identical-type variant)Typical applicationsTool and mould making — repair and build-up weldingPump, valve and fitting componentsShafts, axles and highly stressed machine partsOffshore, chemical and food technologyAerospace componentsProperties and advantagesPrecipitation-hardening (Cu/Nb) — high strength through ageing (heat-treatment conditions H900/H1025/H1150)Achievable hardness 37–40 HRC per manufacturer datasheetGood corrosion resistance at high mechanical load capacityIdentical-type weld metal for durable, low-crack jointsShielding gas: argon 4.6 or better; adapt heat control to the aged condition of the componentRod form advantage: Ideal for manual build-up welding with constant wire feed — also for repair sites that are hard to access in tools and moulds.Rod form: Rod lengths 1000 mm and 333 mm, Ø 0,2 mm – 0,6 mm. Material analysis (wt.-%)Cr 15.0–17.5 | Ni 3.0–5.0 | Cu 3.0–5.0 | Nb 0.15–0.45 | Mn ≤1.0 | Si ≤1.0 | C ≤0.07 | Fe balance